Rice Lake WLS-C Manuel d'utilisateur

115203WLS-CWheel Loader ScaleInstallation & User ManualTo be the best by every measure

6 WLS-C Wheel Loader ScaleFigure 1-13. Sensor Mounted at Recommended Angle; Rubber Gasket Highlighted4. Place the copper o-ring between the sensor and

WLS-C Wheel Loader Scale - Installation 7Figure 1-14. Location of Installed Proximity SensorFigure 1-15. Installation Location of First Switch40/50 cm

8 WLS-C Wheel Loader Scale1.4 Angle Sensor InstallationPlace the chassis and boom angle sensors as shown in Figure 1-16. They should both be horizonta

WLS-C Wheel Loader Scale - Installation 9Figure 1-18. Angle Sensor Installed On Support ArmNOTE: Angle sensors should be installed in line with the op

10 WLS-C Wheel Loader Scale3. Route the sensor’s wire back to the cab.NOTES: Ensure there is enough slack in the wire to allow the support arm to rais

WLS-C Wheel Loader Scale - Installation 11Figure 1-22. Cables Routed CorrectlyDo not mount the cables too close to the motor, unless they are well ins

12 WLS-C Wheel Loader Scale2.0 Display Indications and Button Functions2.1 Indicator DisplayOnce power is applied, the system performs a self-test and

WLS-C Wheel Loader Scale - Display Indications and Button Functions 132.2 Indicator ButtonsIndicator buttons are your interface for communicating with

14 WLS-C Wheel Loader Scale3.0 CalibrationTo calibrate the WLS-C, you must enter calibration mode. This allows you to alter system settings.3.1 Enteri

WLS-C Wheel Loader Scale - Calibration 153. Press and release the Print/Enter button to confirm the password.You can scroll to another page of the men

16 WLS-C Wheel Loader Scale3.3.1 Calibration procedure1. Scroll to the Get Start Angle menu.2. Raise the bucket up to the start weighing area point. B

WLS-C Wheel Loader Scale - Calibration 1710. Scroll down to the Save and save the Angle CalFigure 3-8. Bucket Position for Get Reset Angle3.4 Dynamic

18 WLS-C Wheel Loader Scale3.5 Empty Calibration3.5.1 Performing an Empty CalibrationUser the following procedure to perform an empty calibration.1. S

WLS-C Wheel Loader Scale - Calibration 19Figure 3-10. Empty Calibration Display3.6 Loaded CalibrationUse the following procedure to perform a loaded c

20 WLS-C Wheel Loader ScaleNOTE: Once the loaded calibration of 10 lifts is completed you must save the data to the memory.Knownload is set based on w

WLS-C Wheel Loader Scale - Calibration 213.7.1 Setting New ValuesSetting a new value, for example setting the Machine Setting, is completed using the

22 WLS-C Wheel Loader Scale3.9 Password (PIN) MenuThere are multiple functions accessible under the Password (PIN) menu.3.10 Machine Setting MenuThere

WLS-C Wheel Loader Scale - Calibration 233.11 Dynamic Setting MenuThere are multiple functions accessible under the Dynamic Setting menu.2 Th. Reg. xx

24 WLS-C Wheel Loader Scale4.0 OperationThe WLS-C system is based on the measurement of the lift cylinder piston pressure (by means of the pressuretra

WLS-C Wheel Loader Scale - Operation 25Figure 4-1. Actual Tare Value4.3 Disabling the Weighing FeatureIn the case that the machine may be required for

iTechnical training seminars are available through Rice Lake Weighing Systems. Course descriptions and dates can be viewed at www.ricelake.com/trainin

26 WLS-C Wheel Loader ScaleFigure 4-3. “Traffic Light” FunctionThe 3 LED’s on the WLS-C, as shown in Table 4-3, will illuminate according to the perce

WLS-C Wheel Loader Scale - Operation 27It is possible to set a factor of ±10% in relation to the calibration value. 110 indicates the maximum positive

28 WLS-C Wheel Loader Scale3. Press and release the Print/Enter button to change the language.These are the languages available:IT = Italian (Italiano

WLS-C Wheel Loader Scale - Operation 294.10 DiagnosticsThe “Sensors Check menu” allows viewing the status of all inputs and outputs.1. Press and hold

30 WLS-C Wheel Loader Scale4.12 Menu FlowchartFigure 4-11. Operation Menu Flow4.12.1 Setting New ValuesSetting a new value, for example setting the M

WLS-C Wheel Loader Scale - Operation 313. To shift the asterisk on the next value to be modified by pressing the Tare/Sel button..4. Increase or decre

32 WLS-C Wheel Loader Scale4.14 Time Setting MenuThere are multiple functions accessible under the Time Setting menu.2 Correction: xxx Settings Correc

WLS-C Wheel Loader Scale - Operation 334.15 Sensors Check MenuThere are multiple functions accessible under the Sensors Check menu.4.15.1 Input Status

34 WLS-C Wheel Loader Scale5.0 Printer (Optional)The WLS-C roll tape printer is a very easy to use 24 columns thermal printer. The printer has a therm

WLS-C Wheel Loader Scale - Printer (Optional) 35WLS-C roll tape printer is provided with a single RJ11 pins connector including a RS232 link. Is also

ii WLS-C Wheel Loader ScaleRice Lake continually offers web-based video training on a growing selection of product-related topics at no cost. Visit ww

36 WLS-C Wheel Loader ScaleFigure 5-3. Printer Dimensions64.59614611288.2

WLS-C Wheel Loader Scale - Warranty 37WLS-C Limited WarrantyRice Lake Weighing Systems (RLWS) warrants that all RLWS equipment and systems properly in

38 WLS-C Wheel Loader ScaleFor More InformationSystem Manuals• WLS-C Wheel Loader Scale Installation & User Manual, PN 115203Literature• WLS-1/WLS

PN 115203 12/10

WLS-C Wheel Loader Scale - Installation 1IntroductionThis manual is intended for use by techniciansresponsible for installing and servicing the WLS-CW

2 WLS-C Wheel Loader ScaleFigure 1-1. WLS-C Component List1.1 Indicator Installation1. Use the bracket as a template to drill holes. Then, mount the b

WLS-C Wheel Loader Scale - Installation 3Figure 1-3. Indicator Mounted in CabFigure 1-4. Indicator Back1.2 Pressure Sensor InstallationThe pressure s

4 WLS-C Wheel Loader ScaleFigure 1-5. 1/4" BSPP Straight FittingFigure 1-6. 1/4" NPT Male to 1/4" Female Straight FittingPressure senso

WLS-C Wheel Loader Scale - Installation 5Figure 1-10. Flange Welded to Hydraulic Line at Desired AngleFigure 1-11. Sensor Mounted at Non-Recommended A